engineer

tim   .

                                                      


newpad.gif (50 bytes)

.   hunkin

                                                         


cartoonist

 

MAKING  REVOLUTION

I love living in the UK, but I wish politicians were more honest that the country is in gradual economic decline and has been for some time (In 1950 the exchange rate was $4 to £1, almost four times what it is today). The idea for Revolution started from the UK’s previous conservative governments ‘levelling up’ policy. Though it enabled some good civic restoration projects there wasn’t enough money to make anyone feel significantly ‘better off’. I thought a much better policy, (though obviously never acceptable to conservative voters) would be ‘levelling down’- taxing the rich to reduce the UK’s ever increasing inequality between the rich and the poor. This wasn’t an obvious idea to turn into an arcade machine so it just sat in my mind for a few years.

 

Then Charles Morgan sent me a video of his Jollyball ball run for the Swiss tourist board. I’ve long been impressed that ball runs can be so amazingly reliable that they often run continuously as art pieces in airports and museums. But I’d never before thought that a ball machine could tell a story or that the ball could be a character. This alone made me buy some 40mm steel balls and start playing with them. At first almost everything I tried just seemed to work, it was such fun. Buoyed by this initial success, I thought it could be the basis of the ‘levelling down’ machine I’d been wanting to make. This was the starting point for making the machine.

 

  First ball run experiments 

I’m writing this a couple of years later, but I think the first stage was experimenting with mechanisms to make a run into a game. The one I found most fun was spreading the track ‘rails’ to let the ball fall between, aiming for one of the of cups below. Once in a cup, the ball would run down a track to knock into a scene of the super rich at play, flipping it over to reveal them ‘levelled down’. 

 

First ball circuit

At this early stage I still thought the machine would be quite simple but as always, the devil is in the detail. It didn’t help deciding the ball had to drop vertically on the scenes, like a bomb, rather than just bashing into the side. Then I reallised the ball had to pause in the cup so you could register your ‘hit’, and then pause again above each scene to focus on the rich at play before their watching demise. But mainly the complexity came from reliably catching the ball after every fall and returning it to the top for the next run. I ended up with a motor to flip each scene (five in all) and another six motors controlling the ball run itself.

 

Final track spread mechanism

 

Final ball drop mechanism 

This took several months but it was steady progress with satisfying moments finding solutions to seemingly insuperable problems. While doing this I was also thinking about the details of the scenes. My first idea was the man about to board a private jet, flipped to being stuck at the back of the queue for a jumbo jet. Making a prototype with distorted perspective, I found that, though different in scale, the jumbo jet perfectly replaced the position of the private jet. I really liked the effect so decided to think up equivalents for the other scenes. So the stately home flips to a victorian prison, the golf buggy to a road sweeper and the opera house to a bingo hall. The final desert island scene remains physically unchanged, just their dreams transform to nightmares.

With the scenes and ball run mechanisms complete, the final job was to make the ball tracks to connect the stages together. I invited Andy Plant to come and help and we a had fun week making it all. At the time it seemed amazingly easy – the ball had such weight it really stuck to the track, even going round tight bends. Sadly after Andy left, I found our tracks were far from perfect. 

They would work ten or twenty times perfectly but then randomly the ball would come off. I eventually rigged up my van’s dash-cam to record continuous runs overnight using an output from the PLC to power it. This output was programmed to switch off when the ball was no longer circulating, which meant that the last and fatal run was easy to find. Even so I ended up spending over two months getting the ball to run at least 2000 cycles down every track without falling off. Looking back, Andy and I just hadn’t supported the tracks rigidly enough. A bit of springiness looks great, but allows the ball to behave slightly differently on each run.

 

By the end of all this I was fed up with the whole machine. Even when I finally got it on the pier there were endless teething problems. The worst one was the unpredictability each time the ball dropped into a cup. Eventually I realised that unlike in my workshop, on the pier the machine caught the sun in the afternoon. The cheap opto sensors I’d used to detect a ball in each cup were being triggered by the sun. I had to replace them with posh sensors that only respond to their own LEDs modulated light. This wasn’t easy, I had to bring the whole machine home to do the job. Other problems continued for about nine months until suddenly it all magically became respectably reliable. So finally I now feel more positive about it, particularly because its fun hearing visitors laugh at the transformations and so obviously enjoying their chance to take a swipe at the super rich!

 

 

 

home

search

about the site

site
map

links to
other sites

where to see stuff

contact me